[OpenSPIM] OpenSPIM Digest, Vol 32, Issue 5

[Anthony, Neil]

Hi Mike, thanks for that info.

Can you please tell me if it's possible to use the presets in the OpenSPIM plugin?  For example, can I setup some presets for red channel and green channel and then get OpenSPIM switch between during the acquisition?

Thanks
Neil

-----Original Message-----
From: openspim-bounces at openspim.org [mailto:openspim-bounces at openspim.org] On Behalf Of Michael Redd
Sent: Monday, December 21, 2015 11:20 AM
To: openspim at openspim.org
Subject: Re: [OpenSPIM] OpenSPIM Digest, Vol 32, Issue 5

The Stradus is not integrated with the Openspim plugin so power cannot be controlled by the slider. You can control the power using micromanager presets: one to turn on the Laser and another to set the power level. I am not sure why you need to turn the laser on before changing the power level, but in my experience that is what you need to do. Email me if you need further details.

cheers
mike
> On Dec 19, 2015, at 11:00 AM, openspim-request at openspim.org wrote:
>
> Send OpenSPIM mailing list submissions to
> openspim at openspim.org
>
> To subscribe or unsubscribe via the World Wide Web, visit
> http://openspim.org/mailman/listinfo/openspim
> or, via email, send a message with subject or body 'help' to
> openspim-request at openspim.org
>
> You can reach the person managing the list at
> openspim-owner at openspim.org
>
> When replying, please edit your Subject line so it is more specific
> than "Re: Contents of OpenSPIM digest..."
>
>
> Today's Topics:
>
>   1. Plugin Power Control (Anthony, Neil)
>
>
> ----------------------------------------------------------------------
>
> Message: 1
> Date: Fri, 18 Dec 2015 18:42:21 +0000
> From: "Anthony, Neil" <nantho2 at emory.edu>
> To: "openspim at openspim.org" <openspim at openspim.org>
> Subject: [OpenSPIM] Plugin Power Control
> Message-ID:
>
> <CO2PR05MB681C3681C7F827CCDA4BF8FECE10 at CO2PR05MB681.namprd05.prod.outl
> ook.com>
>
> Content-Type: text/plain; charset="us-ascii"
>
> Hi all,
>
> Has anybody got any experience with the power control slider not working when connected to a Stradus laser over a COM port?  I have made a short unlisted YouTube to show what's happening and save me a few words here:
> https://www.youtube.com/watch?v=2JEiMHxS69w
>
> Key points:
>
> -          I cannot control the power of the active shutter using the power slider - it jumps back to zero
>
> -          When changing through the device controller (which works as it should on the laser itself) it shows what looks like a multiplication factor gone wrong somewhere on the slider.
>
> -          At certain values the slider value jumps back and forth, which is strange
>
> -          It only works for one of the lasers.
>
> Any thoughts would be much appreciated.
>
> Thanks
> Neil
>
>
>
> ________________________________
>
> This e-mail message (including any attachments) is for the sole use of
> the intended recipient(s) and may contain confidential and privileged
> information. If the reader of this message is not the intended
> recipient, you are hereby notified that any dissemination,
> distribution or copying of this message (including any attachments) is
> strictly prohibited.
>
> If you have received this message in error, please contact the sender
> by reply e-mail message and destroy all copies of the original message
> (including attachments).
> -------------- next part -------------- An HTML attachment was
> scrubbed...
> URL:
> <http://openspim.org/pipermail/openspim/attachments/20151218/f1752849/
> attachment-0001.html>
>
> ------------------------------
>
> _______________________________________________
> OpenSPIM mailing list
> OpenSPIM at openspim.org
> http://openspim.org/mailman/listinfo/openspim
>
>
> End of OpenSPIM Digest, Vol 32, Issue 5
> ***************************************

Michael Redd
Imaging Specialist
Cell Imaging Core Facility
University of Utah
Radiobiology Bldg, Room 48,
30 N 2030 E, Salt Lake City, UT 84112

michael.redd at hci.utah.edu


_______________________________________________
OpenSPIM mailing list
OpenSPIM at openspim.org
http://openspim.org/mailman/listinfo/openspim

________________________________

This e-mail message (including any attachments) is for the sole use of
the intended recipient(s) and may contain confidential and privileged
information. If the reader of this message is not the intended
recipient, you are hereby notified that any dissemination, distribution
or copying of this message (including any attachments) is strictly
prohibited.

If you have received this message in error, please contact
the sender by reply e-mail message and destroy all copies of the
original message (including attachments).